Repair Your Fishing Rod Handles This Winter

Repair Your Fishing Rod Handles This Winter

For many fishermen, these winter months mean no fishing.  That is, unless you live in Florida like Mud Hole, or you have caught the ice fishing bug.

In any case, it is still a good time of year to take a look at your fishing rods, and do any maintenance necessary so when it is time to go fishing; you know all your equipment is ready to go.

This article highlights some common best practices for maintaining or repairing your EVA and cork fishing rod handles and grips.

Cleaning Existing Cork and EVA Handles

To be safe, always use any recommendations the manufacturer may list, or test on scrap pieces if available – just to make sure you are happy with the results.

In general though, here are a few suggestions;

First, you can try using some warm – lightly soapy – water and a sponge.  Gently rub the sponge over the grip and you may need a little more pressure for problem areas.  When finished, be sure to use plain water to wash all the soapy residual off.

For cork handles – let the cork dry completely.

Then, try applying a sealant like Cork Seal by U-40, it’s only about $5.

Cork Seal is designed to seal the surface of cork rod handles.

It prevents the penetration of soils and other foreign matter transferred to the grip area from the fisherman’s hands.

It enhances that “cork feel” and toughens the cork to aid in the prevention of sloughing and chipping of the cork surface.

Cork Seal soaks into the cork and seals in depth.  Once it is dry, dirt, grime, and salmon egg residue are easily washed off with soap and water.

Second, we have heard that many fisherman use Mr. Clean eraser pads.  Start by getting them little wet, and then gently rub over the cork handle, with a bit more attention to problem areas.  Looks like new afterwards.

Again, once the cork handle completely dries, apply cork sealant.

Repairing Existing Cork Handles

Over time cork handles can not only get dirty, but also dry out and crack – or develop small areas where the cork may have chipped off.

To fill in those cracks (or even fill in smaller holes) try using Elmer’s Carpenter’s Wood Filler.

Heat Shrink Grip Material For Fishing Rods

This works excellent on all kinds of cork grips and can be used to repair and recondition otherwise sorry looking handles.

Some feature benefits of using this are:

  • Sands easily to a smooth finish
  • Resists shrinking + cracking
  • Easy water clean-up
  • Solvent free

Some key things to keep in mind:

Preparation:  Surface must be clean & dry. Cork, filler and air temperature should be above 40°F.

Filling:  Apply to cork pits and grooves with a spatula, putty knife or similar tool, and be sure to remove any excess.  Note: Deeper repairs may need 2 or more fillings.

Sanding:  Sand shallow repairs after 15 minutes (or when completely dry).  Deep repairs may take upwards of 2-8 hours.  Use medium grit sand paper.

Finishing:  Before filling, test stain on scrap cork with filler.  Apply cork seal or other finish after 24 hours.

You can also use a heat shrink grip material, as described below (in Repairing Existing EVA Handles).

Repairing Existing EVA Handles

When your EVA handles are a mess and the material is fading, the easiest way to get that handle looking new is to use heat shrink tubing.

Colored Heat Shrink Grip Material by CRB comes in a wide variety of colors and sizes, and costs anywhere from $8 to $20.

Heat Shrink Grip Material For Fishing Rods

Heat shrink grip material is a great choice to rejuvenate old, worn out fishing grips. It works on cork, EVA, Hypalon and cork tape. It also works extremely well on new customized applications.

The product is available in 4 sizes to adapt to all applications.  It has a soft feel which will reduce fatigue on the angler when fighting fish.

Some typical rod building and repair applications for this heat shrink grip material are:

  • Replace worn out cork, Hypalon and cork tape fishing grips
  • Use on saltwater or freshwater rods
  • Use on new custom rods
  • Use on projects that require a new grip
  • Heavy wall thicknesses
  • Shrinking temperature of 150° F
  • Easy to install with only a heat gun
  • 2:1 Shrink Ratio

Note:  You may require a heat gun to properly shrink this material.  A Rod Builder’s Electric Heat Gun costs about $25 and is sold separately.

Sealing New Cork Handles

If you are building a rod this winter, or just installing a new cork handle, be sure to use some kind of sealant after install.  It will help maintain the cork handle through the life of the handle.

Try Cork Seal by U-40, it’s only about $5.

Cork Seal is designed to seal the surface of cork rod handles.

It prevents the penetration of soils and other foreign matter transferred to the grip area from the fisherman’s hands.

It enhances that “cork feel” and toughens the cork to aid in the prevention of sloughing and chipping of the cork surface.

Cork Seal soaks into the cork and seals in depth.  Once it is dry, dirt, grime, salmon egg residue are easily washed off with soap and water.

Share This Post